메뉴 바로가기 본문 바로가기

Articles

Roller Culture Apparatus vs. Roll-in Incubator - Roller Culture Configuration Guide

November 03, 2026

Roller culture is a long-established way to grow adherent cells in large quantities. Cylindrical culture vessels (roller bottles) turn slowly and continuously, which spreads a thin film of medium over the whole inner wall. Cells attached to the wall meet this medium as the bottle rotates, and gas exchange with the headspace inside the bottle repeats through the thin film.

 

The name "roller culture" makes it easy to think of one machine, but it needs both a drive that rotates the bottles and a culture environment suited to the cells. In the SH lineup the roller culture apparatus and the roll-in incubator split those two roles. The incubator maintains temperature while the bottles rotate and controls CO₂ where required. This guide explains what each device does, why they are separate, and how to combine them by scale.

 

1. Principle of Roller Culture


Roller culture lays a cylindrical vessel on its side and turns it slowly on a rotating shaft. As the vessel rotates, the medium runs in a thin film along the inner wall, and cells attached to the wall are repeatedly submerged in the film and then exposed to air.

 

Cells can use the whole wide inner wall of the cylindrical bottle as culture surface, not only the bottom of a vessel. This makes it easier to scale up adherent cell culture than static culture in many flasks. Repeated contact and mixing with the medium also helps nutrient delivery and gas exchange.

 

Getting the same culture surface area by static culture takes far more flasks or dishes, whereas roller culture grows more adherent cells in the same space. That is why it has become an established method in processes that handle adherent cells in large quantities.

 

 

2. Role Comparison: Roller Culture Apparatus vs. Roll-in Incubator


 Item 

 Roller Culture Apparatus 

 Roll-in Incubator

Core Function

Drive that holds bottles or tubes and rotates them slowly 

Takes the roller culture apparatus inside and maintain temperature (and CO₂)

 Main Components 

Rotating shafts, driver motor, bottle holders, controller for forward/reverse rotation and angle adjustment 

 Constant-temperature chamber, mirror-finish stainless steel inner wall, double-glazed glass door 

 Temperature control

 None of its own

Ambient +5 °C to 60 °C, ±1 °C uniformity 

(ambient 25 °C, set 37 °C, no load) 

 CO₂ Control 

 

Not applicable

 

 PY series: not applicable. 

PYC series: controllable in the 0–20% range

 CO₂ Sensor and Response (PYC)

 Not applicable

 IR (infrared) sensor, control response within 3 minutes, recovery to 5% within 10 minutes

 Standalone Use 

Small models can go inside an incubator or CO₂ incubator you already own. 

Large models are normally combined with a dedicated roll-in incubator

 Cannot perform rotating culture without a roller culture apparatus 

(it can serve as a constant temperature chamber for other uses)

 

Roller culture needs both a drive that rotates the bottles and a culture environment suited to the cells. A small roller apparatus can be placed inside an existing incubator. Large equipment such as the CGⅢ series is hard to fit inside an ordinary incubator, so it runs together with a dedicated roll-in incubator.

 

 

3. Why Two Devices?


A shaking incubator combines shaking and a constant-temperature chamber in one instrument, so a single machine completes the culture. Roller culture instead separates rotation (the roller culture apparatus) from environment control (the roll-in incubator), and you combine the two to suit your purpose and scale. 

 

The reason for the split is flexibility. A mini roller apparatus that turns only a few tubes or bottles can go inside an incubator or CO₂ incubator you already have. A large apparatus that turns many bottles at once must be set up as a pair with a dedicated roll-in incubator to run in a stable temperature and CO₂ environment.

 

Shaking and roller culture share the idea of using physical motion to improve culture efficiency, but they are generally used for different cells and goals. A shaking incubator moves its platform in an orbit and is widely used for liquid culture of bacteria and yeast and for large-scale culture of suspension animal cells such as CHO cells. Roller culture rotates cylindrical vessels and is specialized for large-scale culture of adherent (monolayer) cells. A roller culture apparatus run at higher rotation speed can also be used for suspension culture (see the CG-06F in section 4.1), so the two methods are not strictly divided by cell type.

 

 

4. Configuration by Scale


Small units can share an incubator you already own, while large units need a dedicated roll-in incubator.

 

Scale / Model

Installation 

Recommended Environment 

Mini Rollers (MR-01U, MR-03U) 

Inside an existing incubator 

Humidified / CO​2​-controlled 

Benchtop (CGI-06F, CG-06F)

Standalone or inside an incubator

Incubator optional, depending on culture requirements

Large Capacitiy (CGIII Series) 

Dedicated roll-in incubator 

PY / PYC Series 

CO​2​-Sensitive Cell Lines

PYC Series recommended

CO​2​-controlled environment

 

4.1 Benchtop small-capacity lineup: CGI-06F vs. CG-06F


The CGI-06F and CG-06F are both benchtop six-bottle models. Both use the same four-wheel drive design, which rotates without slipping. The difference between them is the rotation speed range. 

 

Parameter

 CGI-96F

CG-06F

 Recommended Culture

 Adherent Cells

 Suspension Cells

 Rotation Speed 

 0.05~1 rpm

 1-15 rpm

 Rotation Speed (r/h)

 3-60

60-900 

  Bottle Capacity

  6 Bottles

6 Bottles  

  Drive System

 Four-Wheel Drive 

 Four-Wheel Drive 

 

r/h means revolutions per hour, so 60 r/h equals 1 rpm. High-speed rotation suits suspension culture, but rotation speed alone does not decide the result. Rotation speed and medium volume together affect cell attachment, liquid flow and nutrient delivery, so check them against your cell line and vessel conditions.

 

 

5. Applications and Use Cases


Roller culture is widely used in processes that must produce viruses in bulk from adherent cell lines, such as cell-based vaccines and virus propagation. It is also used in viral vector production research and cell-based antigen production.

 

Depending on the operating method and cell line, it is also used for suspension or non-adherent cell culture, such as monoclonal antibody production with hybridoma. It also applies to large-scale passaging of adherent cell lines whose culture surface area is too small in static culture (flasks) alone. For mass-production processes that must grow as many cells as possible in the same culture room space, it is worth considering as a way to raise culture efficiency per unit of space.

 

 

6. Selection Criteria


Start from your cells and bottle count, then decide whether you need CO₂ control and a paired incubator.

 

1 - Confirm the culture method and cell line first. Roller bottles are generally used for large-scale culture of adherent cells, but they can also serve suspension culture depending on rotation speed and operating conditions. For adherent (monolayer) culture, consider a low-speed rotation model. For suspension culture, compare high-speed rotation models with shaking or stirring methods.


2 - Check the bottle count and the apparatus's loading capacity. Options range from 6 bottles (CGI-06F, CG-06F) to 16, 30, 40 and 45 bottles (CGⅢ series).


3 - Check the medium's pH buffering system and whether CO₂ control is needed. If conditions such as a bicarbonate buffer system require external CO₂ control, choose the PYC series (CO₂-controlled roll-in incubator). If your medium and operating conditions need no separate CO₂ control, the PY series may be enough.


4 - Check whether you need the apparatus and the roll-in incubator together. Small models (MR series) can often use an existing incubator or CO₂ incubator. Large models (CGⅢ series) are normally combined with a dedicated roll-in incubator (PY/PYC) to get a stable constant-temperature and CO₂ environment.


5 - Check installation space and power. For example, the PY-16 has internal dimensions of 745 × 690 × 1115 mm, power consumption of 1250 W and temperature uniformity of ±1 °C (ambient 25 °C, set 37 °C, no load), so confirm space and power capacity beforehand.

 

In short: decide the target cells (adherent or suspension) and the number of bottles, then choose between the PY and PYC series by whether CO₂ control is needed, and check whether your scale calls for pairing the apparatus with a roll-in incubator.

 

FAQ


Q: Can I use a roller culture apparatus as soon as I buy it?


: Small models such as the mini roller (MR series) can be placed inside an incubator or CO₂ incubator you already own. Large roller culture apparatus such as the CGⅢ series should be configured together with a dedicated roll-in incubator (PY/PYC series) that provides the constant-temperature (and CO₂) environment, so that it runs stably.

 

Glossary

  

Adherent cells: cells that grow attached to a vessel surface. The larger the culture surface area, the more cells you can grow.


Suspension culture: a method in which cells grow floating in the medium instead of attaching to a surface. Equipment such as shaking incubators, or the CG-06F with its high-speed rotation, is used.


Bicarbonate-buffered medium: a medium that uses bicarbonate to maintain pH. It requires CO₂ concentration control, so the PYC series is a candidate.


Roll-in incubator: a constant-temperature chamber into which the whole roller culture apparatus is rolled in, maintaining the temperature and CO₂ environment.



Explore Our Roller Culture Apparatus / Roll-in Incubators Models 

Browse available models and detailed product specifications

Large Capacity Roller Culture Apparatus - CGⅢ series

Bench Top Roller Culture Apparatus - CG, CGI series 

Roll-in Incubator - PY, PYI series 

 

Looking for the Right Cell Culture System? 

Share your target cell type (adherent or suspension), required bottle capacity, and CO₂ control needs, and we will help you select the most suitable Roller Culture Apparatus and Roll-in Incubator configuration.

Contact: martin@samheung21.com I jay@samheung21.com 

______________________________________________________________________________________________________________________________________

 

Written by Jay Bang, Bioengineer, SH Scientific